January 31, 2015
Prevention tire: tire pressure down promptly repair
The hot summer is high season car tire. Due to the high temperatures,
low quality or if the tire itself tire pressure is too high, the tire
after gas expansion will lead to a puncture. Therefore, we recommend
that owners will be tire reduced by 10%, adjusted to 2.2 kpa.
Owners should pay more attention this season on tire maintenance, if
damage is discovered, it should be promptly repaired or replaced. If you
have patched the tire, it is best to put the rear wheels or as a spare
tire. In addition, particular attention not to let the summer tires
collision obstacle, because it is easy to make the tire sidewall
injuries caused problems.
Reminder: If the tire which occurs in the driving, the driver applied the hand tightly control the steering wheel, slow step on the brake, the vehicle smooth deceleration stop. Do not be an emergency brake, because it is easy to cause the flick even rollover.
Water temperature exceeded: Timely parking thermal cooling
Summer car drivers who not only baked, vehicles will be unable to
withstand high temperatures, excessive water temperature is relatively
common, even "boil" boiling. Summer car owners should always pay
attention to see when the water table, look at whether the water tank.
Driving, if you find the water table pointer nearing the red line, it
should reduce the speed as soon as the car drove into a cool place to
stop. To avoid engine damage, do not immediately turn off after
stopping, but should let the engine idle for a period of time before.
If the water temperature is still not fall down, you should turn off the car, check the engine coolant. But be careful not to open the radiator cap immediately, otherwise it is easy to steam burns. If it is because of lack of coolant, it would first make up.
Reminder: If the water temperature is too high the phenomenon, do not let the car on long journeys, because for a long time with a lot of damage to the engine water temperature is not under normal circumstances; do not slow down especially not choose congested roads.
Auto ignition: Reducing modified periodically check
Prevent the car ignition; the most basic method is to periodically do
maintenance to the car, check the engine, and an oil circuit, to see
whether the aging and oil spills. Do not store in a non-standard vehicle
repair or modification, because of some wrong operation of Luanda
wires, easy to friction is not effective at a fixed, will be dangerous.
If the modified car, especially lights, sound, etc., should be
comprehensive examination. In the hot summer, do not lighters,
fragrances, air fresheners and other flammable items placed under
prolonged exposure to high temperatures inside the car to avoid swelling
caused by physical explosion sparking spontaneous combustion; After a
long journey, it should be appropriate to let the car rest what to avoid
overload.
When driving, vehicle owners should be aware of signs of spontaneous combustion, such as an odor, abnormal sound or vehicle electrical malfunction and so on.
Reminder: The best car standing on a fire extinguisher. Once spontaneous combustion, the first car in the right place few people pull over, turn off the heat, remove the fire extinguisher, look for fire points to the part of the cooling tank and burning fire to avoid explosion.
Here we recommend some OBD diagnostic tools can help you test your car by yourself, such as: Launch X431 Diagun III, Launch X431 Pro3, Launch X431 IV, Autel MaxiDas DS708 and so on.
Posted by: obdtools at
06:30 AM
| No Comments
| Add Comment
Post contains 615 words, total size 6 kb.
January 30, 2015
Still smell the air cleaning
Performance: "I'll wash myself before coming once every summer air
conditioning is the fear of unpleasant smell, but not for a long time
after this cleaning, find air conditioning or smell, air conditioning
useless for a long time, is it going to change?"
Diagnosis: "odor generation, mostly due to the accumulation of air
conditioning condensate pipe, forming a dark and humid environment,
making the mold reproduction, light cleaning is palliative approach
should find the problem from everyday driving habits." service
department official said, a lot of people used to wait for parking was
off the air conditioner, this will cause condensation deposition in the
pipeline, the condensed water and airborne dust debris attached to the
evaporator surface together will breed a lot of bacteria, with the wind
blowing contaminated air-conditioning throughout the interior air.
Therefore, the best in destination thirty-five minutes before switching
off the air conditioning compressor, the fan idling, due to increase air
flow, parking in front of the temperature rise inside the air
conditioning ducts in order to reduce the generation of condensate, dry
air-conditioning system.
Air conditioning and refrigeration effect is reduced
Performance: "There never used air conditioning six months, the weather
is hot every day, every time after the start of air conditioners, will
be long before refrigeration and cooling effect simply is not obvious,
and there is no air conditioning around the abnormal situation, is a
quick return thing? "
Diagnosis: For Nissan owners Wong this doubt, Nissan shop service
manager said that some vehicle air conditioning deactivated after nearly
six months, the refrigerant may have leaked, need to replenish, repair
shop owners to repair the same time, remember to remind people not to
forget to clean the repair evaporator and air conditioning filter,
clogging them will affect the cooling effect.
After the air conditioning abnormal noise starts
Performance: "I opened the air conditioning, the air conditioning vent
given the slightest sounds, there are what look was not any average
every few minutes, this is what happens?"
Diagnosis: air conditioning abnormal sound is generally abnormal sound
air-conditioning compressor, air conditioning compressor can feel it in
the vicinity of the sound. Such abnormal sound is generally due to the
refrigerant composition of air and water caused by doping. If the
situation remains the same after adding refrigerant, which is located
near the compressor abnormal sound position, then the compressor
internal mechanical structure damage greater chance; If abnormal sound
relapse after a period of time, and is located inside the center
console, then dried to reduce the chance of bottles efficiency larger.
After successive investigation, find the key issues in order to remedy.
Open air car difficult to mobilize
Performance: "My car displacement of only 1.3L, usually I do not gnaw
with air conditioning, two days before the main is too hot, put the air
conditioning turned on, I think after the open, the car is difficult to
start than usual, why?"
Diagnosis: "Engine load is too large, you should first open air outside
the loop" This is Ford Hunan Freshwater shop service personnel given an
explanation. It is particularly worth mentioning is that if the car just
after launch, immediately start the air conditioning, air conditioning
maintenance practice is taboo, not only cannot play the role of rapid
cooling, but also has a lot of damage to the air conditioning? According
to reports, a car parked in the sun, the temperature inside the vehicle
may be up to sixty to seventy degrees, you should first car windows and
doors, and etc. twenty-three minutes before the heat is discharged into
the launch vehicle. While the first open air outside the circle, to be
close to the temperature inside and outside, and then close the window,
the use of the loop. Under normal circumstances every 5,000 km or three
months on the air conditioning filter cleaning once or 12 months to
replace air conditioning filters every 20,000 km. This will ensure that
you can enjoy the fresh clean car interior environment to ensure good
health.
Here we recommend some auto diagnostic tools can help you test your car by yourself, such as: Launch X431 GDS, Launch X-431 PAD, Autel MaxiSys MS908, Autel MaxiSys Pro MS908P and so on.
Source: http://www.focalobd.com/blog/automotive-air-faqs-4-tips/
Posted by: obdtools at
09:06 AM
| No Comments
| Add Comment
Post contains 714 words, total size 7 kb.
January 27, 2015
The first step to check the circuit
Because many irrigations rain will performance cars might have an impact
on some parts, lead to serious car not normally open. After the water
is likely to cause a short circuit, if you cannot turn off the road in
the ignition to start the engine again, or they may easily cause engine
scrapped. If wading, then promptly after the adoption of the circuit
device processing, you can use non-fibrous tissue and textiles will dry
the circuit 11, re-start.
Also, check the brake system is also very important.
Because of the braking system has a very strong adhesive force, the rain
is very easy to enter the brake fluid, it will affect the braking
effect, may cause serious brake failure, recommendations rain to a
professional auto repair shop to be checked, to prevent future trouble.
The second step is the conservation of the chassis
Summer temperatures are high, coupled with the rain hit, chassis
vulnerable, gas, dust, noise, moisture will penetrate the body from tiny
holes in the chassis, so that the body rust, flaking. So you want to do
some maintenance work on the chassis after heavy rain.
In addition to the simple and clean, "sealed plastic chassis" is also a
good choice. It enables the chassis and isolated, to corrosion, rust,
soundproof function and prolong the life of the body. "Sealed plastic
chassis" to use special detergent before removing the chassis attached
to the asphalt, oil, and dry, any dirt will affect the firm's degree of
plastic closures. Before sealing plastic, but also part of the heat
transmission, exhaust system are blocked, so as not to affect the normal
operation of these sealed plastic components.
Step third Check headlight
Easily lead headlights rain water. After the headlight brightness will
be affected water, water may damage many headlamps, the lights also make
changes happen irradiation direction to traffic safety and security.
Therefore, the water is very important to check the headlights.
If you find a mist in the headlights, and the high beam headlamps can be
opened also opened ten minutes to see if the lights inside the mist
began to disappear, whether we can completely disappear after one hour,
if you do not have to worry about the disappearance of the but if there
is fog, it is necessary to professional service station handled.
The fourth step in the car dehumidification
In fact, dehumidification work should be done when it rains. Should open
the cold when it rains, it can not only remove the fog, as well as
dehumidification function. The rain stopped even have to pay attention,
to get rid of as soon as possible the accumulation of moisture or prone
to mildew and other conditions. In addition to air conditioners
dehumidify the car, the best dehumidifier to buy a simple box, so that
after the car parts are not easy to damp overnight. Another roll of
toilet paper placed inside the vehicle also has the effect of
dehumidification.
In addition to welding and rain doors welded body part susceptible to
rust corrosion, internal door hinges, lock and other iron parts are
covered by the door trim, but also easy to damp, so the weather was fine
when the owners can find a shady place, all the doors and trunk lid
fully open, so that the car's exhaust moisture, ventilation, and then
the car floor mats, seat covers removed, rinse dry.
The fifth step the inside vehicle sterilization
Summer temperatures due to factors such as rain relatively easy to breed
a variety of bacteria so the interior space for disinfection
sterilization is particularly important. Clean place emphasis should be
seats, air conditioning vent, in the control panel and around a corner.
You can use a professional car interior cleaner, wipe with a dry cloth.
Clean the center console when the cleaner to prevent infiltration of CD,
speakers, radios and other electrical equipment corrosion of electrical
components.
The Six step clean appearance
Car as it were, after the rain do not bother to wash oh, otherwise it
will seriously affect the personal image. In fact, the problem is not
only a personal image, rainy day outside in addition to sewage and
sludge, acid rain also contains a substance on the body and the paint
has a serious injury, if not promptly treated, over time, the body will
lose their luster in turn affect the appearance.
Want to prevent acid rain damage to the body, the most simple and
effective method is waxing, and want to achieve a very lasting effect
that will have to be sealed to protect the glaze, both to prevent paint
fade aging, and thus protect the paint from injury.
Some OBD diagnostic tools will help you test out your vehicle on your own, for example: Launch X431 IV, Launch X-431 PAD, Autel MaxiSys MS908 and so on.
Source: http://www.focalobd.com/blog/6-steps-maintaining-your-car-after-the-rain/
Posted by: obdtools at
07:49 AM
| No Comments
| Add Comment
Post contains 819 words, total size 8 kb.
January 26, 2015
Myth one: the warranty period length = lower cost
Many owners believe that car manufacturers extended warranty period,
their car costs will be significantly reduced, but in fact, the warranty
is like insurance, there is a problem only when the car that he can get
the benefits brought by this policy. Of course, power train maintenance
costs are very expensive, usually, the cost of a car power train system
to account for 35% -40% of vehicle costs. Therefore, power train
systems need to be replaced soon would be great for consumers to spend.
Extended warranty period, no doubt to avoid the risk of consumers
themselves such a huge overhead.
In fact, the main purpose is to extend the warranty period to develop
good guide owners regularly scheduled Cheng conservation habits to guide
owners through professional conservation in the 4S shop, will be
maintained better condition, until the owners transfer, will find its
residual car increase the value, much better than spending during
curing, in fact, this is the real protection of the interests of
consumers.
Myth two: Maintenance seat of your pants do not follow the periodic table
Each car will be given when the owner of a maintenance of the periodic
table, was told to do what at what time of the maintenance, but most
owners driving on, as long as you feel good, not out what problems will
gradually put in back of the head; another part of the owner is out of
the previous driving experience, self shorten maintenance mileage, such
as the maintenance requirement is 8000 km, then he put the car in the
6000 km when open to the 4S shop; or not to the maintenance time to 4S
shop maintenance, the result is more money. In fact, does not the more
the better ground vehicle maintenance, mileage specified by the
manufacturer is based on the performance of full understand of the body,
and thus only the best data set.
Myth three: do not go over the warranty period 4S shop
Vehicle about two years, this car is the best condition when the state
of the body at this time to reach various parts of the ideal state, how
to make this state continue? Rely on the professional conservation 4S
shop: a long drive regularly scheduled maintenance, the use of original
oil and accessories will naturally extend the useful life of the car.
Reporters have done more, the same two opened a five-year car, a 4S shop
has been doing maintenance, the other one in the first 2 years after
the end of the warranty period do not go to the 4S shop maintenance,
condition is different, open up the car think it is two generations.
Myth fore: manufacturers do not warranty consumables
Currently most of the manufacturers don’t have warranty of consumables.
In fact, this type of accessories if you really have quality problems,
usually in the 2000-3000km affirmative exposed, not a problem if used
5000 km theoretically would not be a problem, unless you use improper
methods. Therefore, the manufacturers to give three months or 5,000 km
warranty actually buy an insurance policy for consumers, eliminating the
owner's worries.
Some OBD diagnostic tools can help you test your car by yourself, such as: Launch X431 Pro3, Launch X431 V Pro, Autel MaxiSys Pro MS908P and so on.
Source: http://www.focalobd.com/blog/4-common-car-maintenance-mistakes/
Posted by: obdtools at
07:31 AM
| No Comments
| Add Comment
Post contains 561 words, total size 5 kb.
January 24, 2015
1. The correct oil, the use of clean fuel.
2. Vehicles will be in time scrapped and updates.
3. Does not change the vehicle and cause chaos emissions exception.
4.
The normal use of the car, don't the degree of speeding, overloading,
avoid rapid acceleration, constant speed driving as much as possible.
5.
Periodic maintenance. It turns out that the car maintenance car
emissions quality is very important. Some car factory emissions when
qualified, but the course will appear this kind of problem that requires
maintenance; make their car in a good running condition. Maintenance is
not timely; it will result in high emissions due to more pollution.
Such as: ground investigation automotive ignition systems, to detect
leaks, check the choke, check the air ducts, use a clean filter,
avoiding the burning of oil, avoid the use of low-grade lubricants.
OBD2 Code system malfunction repaired promptly. Vehicle inspection once a year
for automobile emissions control role is limited. But after installing
the OBD car is completely different, and it can always monitor the
emission levels of vehicles. Once released, if not standard, OBD warning
will be issued promptly notify the driver to repair. Euro â…¢ most
critical is to use OBD.
6. Select the "green tire". The so-called "green tire" also known as environmental tire or low pollution tires.
"Green"
mainly kept in the case when a good grip without losing its original
performance, lower tire rolling resistance, thereby reducing fuel
consumption and vehicle emissions, effectively protect the environment.
Back in the 1990s, tire engineers discovered that if you use special
treatment to replace the traditional carbon black, silica tread rubber
as a reinforcing material can not only reduce carbon black in tires and
carcinogenic aromatic oils contaminated by tire wear air, and tire
rolling resistance also become smaller, lower fuel consumption,
emissions reduction, and greater environmental effects.
7. To
reduce vehicle pollution. Do not be free to interior decoration; not
inferior car perfume or air freshener; encountered serious traffic jam,
or follow the vehicle exhaust emissions may be excessive, you should
close the window, the air conditioner, heater switch to the car from the
circulation patterns; regularly check the engine cover and chassis
leaks when there is gas leak found in the car, not the open air, not to
sleep in the open air car, to avoid danger.
When using the air
conditioning will be sucked into a lot of dust, the formation of dirt,
over time, mildew, and then distribute to the car through the air
conditioning in the car easily inhaled, every once in a while, the air
conditioner to maximum block, blowing on half an hour can effectively
prevent dust accumulation; note near the mouth of the intake items
removed to ensure normal air circulation and so on.
Some vehicle diagnostic tools will help you test out your vehicle on your own, for example: Launch X431 V Pro, Launch X431 Pro3, Autel MaxiSys MS908 and so on.
Source: http://www.focalobd.com/blog/seven-great-advice-of-automotive-engineers/
Posted by: obdtools at
06:55 AM
| No Comments
| Add Comment
Post contains 499 words, total size 5 kb.
January 23, 2015
Adjust the concentration of oil
Seasonal
maintenance time, but also to look at the concentration of particular
issues automobile oil. Professional advice in the selection of the
engine oil, need to take into account the conversion issue season.
Because oil viscosity with temperature change, the viscosity becomes
high in winter, summer, the viscosity becomes low. Therefore
transformation occurs at a temperature, when the weather is cold you can
use lower viscosity oil.
Concerned about tire wear condition
Fall season, automobile maintenance first thing to note tires.
Especially before eleven travel, more should pay attention to the
"health" of the tire. Because the hot summer weather, tires due to the
high temperature friction and wear will be relatively large, it will
crack. Driving, crack increases. Therefore, owners should pay particular
attention to the situation to see whether the check tire wear appear
serious to ensure road safety.
Clean air filter
Vehicle air-conditioning routine cleaning cycle is once every six
months, but when the season is the best time to dust. After a summer of
use, air filter odor may occur if the filter can be removed by washing
with water, simple and economical. But if the activated carbon material,
you cannot use this method. In addition, the air-conditioning blower
should dust.
Clean interior
A long summer,
laying carpet and inside flooring, cushions and other interior seat on
the car as well as some of the dead may be covered with dust, the
breeding of various types of bacteria. Under the catalysis of summer
sun, the dust is relatively easy to produce odor; once cold days, the
car windows closed, the air inside begins to become cloudy, odors and
bacteria will constitute a human health hazard. At the time of the
season as the vehicle can do a steam sauna, photo catalytic disinfection
clean?
Some Auto diagnostic tools can help you test your car by yourself, such as: Launch X431 Diagun III, Launch X-431 PAD, Autel MaxiDas DS708 and so on.
Source: http://www.focalobd.com/blog/best-4-methods-to-do-car-maintenance-in-the-summer-and-fall-season/
Posted by: obdtools at
06:12 AM
| No Comments
| Add Comment
Post contains 344 words, total size 9 kb.
January 22, 2015
For increasingly soaring oil prices, some of the economic strength is
not strong young owners, helpless sigh, "cannot afford" In fact, if a
little attention in the daily driving habits, maintenance, can often
save a lot of fuel consumption, reporter summed up five strokes coup
nowadays more popular fuel for your reference.
Less than 10 minutes travel time
Driving style affects the car's fuel consumption. Maintain well driving
habits, not only can reduce the wear and tear, and can save fuel. Gentle
driving slow acceleration anticipating the brakes then can avoid panic
stop.
In addition, the travel time should be done to minimize short trips.
Less than 10 minutes of short-haul travel is not only a waste of fuel,
but the car is very negative, because the engine is no chance to really
heat up, which will cause condensation engines. When the iron, the
oxygen and water are mixed to produce rust and rust is detrimental to
the car.
Select suitable lubricant
High quality oil can protect the engine is very easy to understand, but
the quality of the oil can reduce fuel consumption, I am afraid not many
people know. In regard to the use of lubricants in different seasons
using a suitable lubricant can reduce fuel consumption.
Do not blindly choose high-viscosity oil, so make engine friction
increases, some loss of engine power, thereby increasing fuel
consumption.
In addition, select the lubricant is to strike a balance between the
protection of the engine and fuel-efficient. According to the standard
given by the manufacturer and car use environment to select the proper
lubricant is order to achieve the best results.
Hot cars of the time not too long
Some owners prefer to name the morning after the car parked hot car,
this is a good habit, but it is undoubtedly a warm-up for too long
trying to find fault with their pocketbook. In fact, as long as the
engine is able to achieve a stable and normal idle speed can be driving
up.
In addition, in fact, you can let the car slowly driving twelve kilometers to reach the warm-up effect.
Air temperature should be appropriate
Automotive air conditioning energy from the engine, turn on the air of
course will increase fuel consumption, however, is able to achieve
rational use of car air-conditioning cooling effect, while allowing fuel
consumption to a minimum. Energy-saving household air temperature is 24
degrees Celsius, the car is the same.
Some owners believe that the air conditioning to the lowest temperature
of the cooling effect of the best, in fact, this is a misunderstanding.
The result is the lowest temperature to allow the inside temperature
reaches 16 or 18 degrees Celsius, but this is not necessarily a
comfortable temperature, and the compressor work the longest, is the
most fuel approach.
Develop good driving habits
Many car owners driving time are "impatient", often wanton throttle will
make the engine speed is too high and thus increase fuel consumption;
rather mad brakes are applied to push the car forward makes the kinetic
energy into heat on the brakes become useless.
Meanwhile, frequent lane changes driving style also make longer mileage
vehicles, will increase fuel consumption. So usually develop good
driving habits can reduce the useful work done to further reduce fuel
consumption.
Some car diagnostic tools can help you test your car by yourself, such as: Launch X431 Pro3, Launch X431 Diagun III, Autel MaxiSys Pro MS908P and so on.
Source: http://www.focalobd.com/blog/best-5-ways-to-save-money-on-gas-for-your-car/
Posted by: obdtools at
07:04 AM
| No Comments
| Add Comment
Post contains 587 words, total size 5 kb.
January 21, 2015
Note one:
Easy winter frost fog, low visibility, particularly rear-ends accidents.
Lights must be working, especially fog lights, brake light, which is
the winter traffic safety protection.
Treatment: Once the black headlight bulbs to replace as soon as
possible, but also to check the fog lights, brake lights of the case, to
promptly clean after dirty, especially headlights and fog lights should
wipe clean.
Note two:
After the cold winters the number of vehicles to be reduced scrub. Body
waxing is a must, after waxing the body is not easy to wet, icy winter
difficult phenomenon. Rinse with cold water in winter cannot be directly
vehicles, higher front car after the engine warming temperatures, rapid
cooling with cold water, to paint the negative, but not directly wash
engines.
Note three:
Winter tire rubber hard and relatively brittle, friction coefficient decreases, winter tires should pay attention to skills.
Treatment: tire pressure is not too high, but more cannot be too low,
low external temperatures, the tire pressure is too low, soft tires
serious can accelerate aging. Always clean up winter inclusions within
the tread try to avoid using up over more than two tires, but also to
replace the larger tire wear. Tire wear different degree of internal and
external, to ensure the safety of reducing wear, the tire should be
periodically change position.
Note four:
Fear battery temperature, low temperature environment is much lower
capacity battery capacity than normal temperature. Low temperatures will
significantly reduce battery capacity, so for not maintenance-free
batteries, if used for a long time, the battery should be sent to the
repair shop for a thorough charge.
Treatment: Before the advent of the cold season, they should supplement
battery electrolyte, the electrolyte adjusting the proportion of good,
while cleaning the battery terminals and apply special grease to protect
and ensure reliable starting and prolong battery life.
It should be noted that, due to the cold weather, the engine oil
viscosity increases, before you start the engine, open switches the
engine warm-up, re-ignition is started. If the vehicle is not easy to
start the best start again every 30 seconds or so, avoid continuous
ignition, preventing the spark plug too wet, the motor burned or battery
power is exhausted. When you start the vehicle in order to save power,
it is best to open other electrical ignition device.
Some car diagnostic tools can help you test your car by yourself, such as: Launch X431 V Pro, Launch X431 Pro3, Autel MaxiDas DS708 and so on.
Source: http://www.focalobd.com/blog/winter-vehicle-common-problems-and-solutions/
Posted by: obdtools at
06:12 AM
| No Comments
| Add Comment
Post contains 426 words, total size 4 kb.
January 20, 2015
Automobile shock absorber is used in the process of wearing parts,
shock absorbers work is good or bad, will directly affect the stability
and other parts of the life of cars so we should make the shock
absorbers are often in good working condition. Use obd2 scanner can test the shock absorbers work is good.
1, so that cars on the road in poor condition after driving 10km road
parking, touch shell shock absorber, if not hot enough, indicating no
resistance inside the shock absorber, shock absorbers do not work. At
this point, you can add the appropriate oil, then test, if the housing
fever, shock absorbers, compared with an internal oil, should add enough
oil; otherwise, indicating shock absorber failure.
2, press firmly on the bumper, and then release, if the car has 2 to 3 times jump, then the shock absorbers work well.
3, when the car is slowly driving and emergency braking, if the car more violent vibration indicating a problem with the shock absorber.
4, remove the shock absorber to be upright, and the lower end of the connecting ring clamp on the vise, pull compression damping lever several times, then there should be a stable resistance, pull up (recovery) should be greater than the resistance to resistance when under pressure, such as resistance to unstable or no resistance, it may be short of oil or internal shock absorber valve parts damage should be repaired or replaced parts.
In determining the shock absorbers have a problem or failure; it should first check whether the shock absorber oil spills or traces of old oil spills.
Seal gaskets, gasket rupture damaged oil storage cylinder head nut loose. May be oil seals, seal washers failure, should be replaced with new seals. If you still can not eliminate leakage, shock absorbers should be pulled out, if they feel there is no issuer or the severity of the moment, and further examination clearance between the piston and cylinder is too large, whether the damper piston rod bent piston rod cylinder surface and if there is scratched or pull marks.
If there is no leakage phenomenon shock absorbers, shock absorbers should check the connection pins, connecting rods, connecting hole, rubber, bushings and other damage, sealing off, break or fall off place. If these were normal, it should be further decomposed shock absorbers, check with the gap between the piston and cylinder is too large cylinder with or without strain, the valve seal is good, valves and valve seat are tight fitting and minus Zhen's done spring is too soft or broken, take grinding repair or replace parts of the way under the circumstances.
In addition, the shock absorber in actual use will be issued by the sound of failure, which is mainly due to the shock absorbers and springs, frame or shaft collision damage or loss, and shock absorber pad dust tube deformation, oil lack of other causes, reasons should be identified, to be repaired.
After the shock absorber during the inspection repair should be carried out in a special test bench performance test, when resistance frequencies 100 ±1mm, its resistance to stretching and compression stroke shall comply with the provisions, indicating damper normal.
Some Auto diagnostic tools will help you test out your vehicle on your own, for example: Autel MaxiSys Pro MS908P, Launch X431 V Pro, Launch X-431 PAD and so on.
Source: http://www.focalobd.com/blog/how-to-use-obd2-scanner-measure-your-output-right/
Posted by: obdtools at
06:36 AM
| No Comments
| Add Comment
Post contains 573 words, total size 5 kb.
January 19, 2015
Summer and autumn, the seasons change, car repair also will naturally become the focus, and then in the autumn
maintenance, the owner should pay particular attention to what? To this
end, the reporter interviewed car maintenance division, hoping to make
professional advice during the fall when the majority of owners of
vehicles of conservation can be targeted more efficiently.
1, car external maintenance
More rain in summer and autumn, rain acidic substances, strong sunlight,
can cause corrosion and oxidation paint, not promptly treated, over
time, the car will lose luster finish. Meanwhile, the dust in the air
and on the road, mud and rain also easy to stick together in the body of
the vehicle, it is easy to make the body dirty, for the car to do a
from cleaning, polishing to waxing, sealing glaze or coating and a
series of beauty care even if the sand more of the autumn season, the
car will still be bright as new surface. If you want to paint care
system, you need to be professional and regular maintenance, many shops
do not have the professional level, if you use a towel containing
sediment particles, will cause damage to the finish, and this damage in a
short time it is difficult to see out of.
In addition, if the car has obvious surface scratches, paint treatment should be done in order to avoid scratches and rust damp parts. In addition, the owners also do not ignore the doors and windows of Polystyrene on maintenance, because the appearance of the rubber body temperature after baking summer usually occurs in varying degrees of aging.
2, chassis systems
As the saying goes, "the first car rotten bottom", in addition to the
tires but also attach importance to check on the chassis. Experienced a
summer rainfall and wading driving, autumn maintenance focuses on car
chassis rust areas. Chassis metal material after hot weather and rain,
"torn" later, prone to rust phenomenon, affecting traffic safety,
therefore, must be on the chassis rust treatment and check if there are
scratches chassis, screw off and so on.
3, the brake system
Regular replacement of brake fluid, check the brakes, avoiding reach the
wear limit, causing a safety hazard. Check the brake has not changed
often weak, deviation, pedaling efforts have not changed the brake
pedal, the need to replace the brake pads, depending on whether the
remaining thickness and uniform wear, brake force is balanced, etc.,
found the problem immediately resolved.
4, battery maintenance
Summer temperatures experienced test, maintenance battery system is also
very important. Today, many car owners to install more and more
electrical equipment, such as a trip computer, car refrigerator,
subwoofer, etc., on the battery system requirements are also increasing.
For this reason, professionals recommend, owners try not to use these
car electrical equipment, so as to avoid excessive battery consumption.
Also, check the electrode wiring at any time there are no exceptions,
because bad habits will greatly shorten the battery life.
5, air conditioning maintenance
Frequent use of car air-conditioning in summer, the owners generally in
use and there are some errors: If the car into the open air, will
increase the engine operating pressure, reduce engine life; air
conditioning running total in the low block, inhalation of dust will
accumulate bacteria, hazardous to their health; time to open the inner
loop, causing the vehicle air pollution and so on. Close the window open
air for a long time, it will cause a lot of bacteria gather in the
compartment, plus air-conditioning duct condensate accumulation, will
breed mold. So, into the fall to do a thorough clean-up and maintenance
of the air conditioning system is particularly important.
6, tire maintenance
Car tires are "feet" in vehicle safety driving, it plays an important
role, and our data show that in highway traffic fatalities, 70% were
caused by tire problems, so for tires maintenance must not be ignored.
Fall due to relatively low temperatures, rubber is easy to harden and
appear more brittle, not only will reduce the coefficient of friction,
but also easier to leak even rolling tires, tire maintenance time to
check whether there is a significant trauma, scratches, etc., make up
the pressure, hit the specified range, while frequent cleaning
inclusions within the tire pattern.
In addition, with the fall of the temperature gradually decreased, gas expansion and contraction will cause insufficient tire pressure within the tire. Therefore, a timely vehicle to check tire pressure condition and avoid inadequate tire pressure caused by abnormal wear. Recommendations to the 4S shop or professional service points do a comprehensive inspection, maintenance cycle and understand its real-time status. If the tread is too shallow or rubber hard and brittle is need to timely maintenance and replacement.
Some car diagnostic tools can help you test your car by yourself, such as: Launch Creader DIY, Launch X431 V Pro, Autel MaxiDas DS708 and so on.
Source: http://www.focalobd.com/blog/6-tips-to-maintenance-your-car-during-the-summer/
Posted by: obdtools at
07:55 AM
| No Comments
| Add Comment
Post contains 827 words, total size 7 kb.
January 16, 2015
Method 1: Washing and waxing. Wash car wash and wax using specialized anti-static, dust the surface of the car can be, the film clean.
Method 2: Instrument Panel Shop wet towel. Usually put a wet towel on the dashboard, or on a regular basis with a sprayer spray a little water in the car, the car can increase humidity, reduce static electricity inside the car.
Method 3: Drink plenty of water. It is better to prevent the owners from their own internal way of static electricity, the more water can increase the skin's surface humidity, and static electricity in a wet state is not going to happen on their own.
Method 4: Use the key addition to static. Acquire other key contact to drive the car in front of the metal parts of the discharge, but do not car keys, car keys inside with theft because the chip, using the car keys discharge car keys may lose theft effect.
Method 5: less open circulating air conditioning. Open cycle air conditioning inside the autumn season will make the car itself has been very dry moisture memory could not recommend ajar window.
Method 6: rub moisturizer. Late autumn or winter, often rubbing hand cream can not only keep the skin moist, but also anti-static, do both. Some people go to wash your hands before going out to drive would be a good idea.
Method 7: use less chemical supplies. Whether human or vehicle should minimize use the chemical class seat covers and floor mats.
Method 8: Using the discharger. Static discharger on the market with air static discharger and take the chain discharger, the effects were good.
Some Car Diagnostic Tool can help you test your car by yourself, such as: Launch X431 V Pro, Launch X-431 PAD, Autel MaxiSys Pro MS908P and so on.
Posted by: obdtools at
07:01 AM
| No Comments
| Add Comment
Post contains 311 words, total size 2 kb.
January 15, 2015
Auto diagnostic tools are used to diagnose the engine, brake, vehicle parts and so on. They
can be plug into the standardized socket on most vehicles and trucks
manufactured after1996. In the fact, using a scan tools can save you
many hours of headache in determining the problem with any car. Besides,
they are very easy-to-use. A common auto repair shops mechanic can learn to use a diagnostic tool in about five minutes.
Instructions: using a car diagnostic tool
1. Determine the type of diagnostic tool required for your vehicle.
There are two main types of sockets, the OBD-1 (On Board Diagnostics)
type, which was the main type of socket made before 1990. And the newer
OBD-2 socket. They both are simple pin-out designs that will allow
access to the computer. The socket is located under the steering wheel,
up under the dash board, and could be hidden by wiring or panels.
2. Plug the diagnostic tool’s adapter plug into the vehicle’s computer
socket, and turn on the vehicle’s ignition, but do not start it.
3. Turn the diagnostic tool on. The display will come on, and after it
communicates with the vehicle’s computer for a few seconds, it will
display an "OK†message or a menu.
4. Apply the menu to find the "stored codesâ€, or the diagnostic codes
that the vehicle’s computer has stored into its memory. These codes are
collected over time, and unless the vehicle’s battery has been
disconnected, they should remain in memory. The scan tool will display
these codes, along with basic data information about the code.
5. Write down the codes that are displayed and the check them.
Automobile repair manuals for the make and model of vehicle will have a
list of these codes and what they mean. Many codes will start with a
letter, followed by several numbers, such as "P0233,†and they are
tripped by sensor that the computer monitors constantly. When the
sensors determine something is wrong with the vehicle, they store the
code in the computer so that the mechanic can determine the issue and
repair it.
Tips & Warnings
1. Buying a diagnostic tool with several adapters can allow it to diagnose multiple cars.
2. Do not attach the obd2 scanner tool directly to the computer or battery.
Source: http://www.focalobd.com/blog/how-to-proper-use-of-car-diagnostic-scan-tools/
Posted by: obdtools at
06:57 AM
| No Comments
| Add Comment
Post contains 392 words, total size 4 kb.
January 14, 2015
If you car had a low flat tire, what would happen? Keeping a normal
tire pressure can make driving safer. An abnormal tire pressure can lead
to serious consequences at any minutes.
1. Increasing fuel consumption
When tire pressure is too low, the contact area between the tire trend
and ground increase, the friction and resistance increase too, so the
fuel consumption increases.
2. Shorten the longevity of the tire
Excessive tire pressure makes the middle of tire trend over-worn; when
tire pressure is too low, the sides of the tire trend over-worn. These
situations will make the vehicle tire scrap in advance.
3. Reducing brake performance
Excessive tire pressure result in less contact area between the tire
trend and ground, reducing the degree of friction, eventually extend the
braking distance.
4. Tire may blow up
A report released by National Highway Traffic Safety Administration
(NHTSA): tire pressure below 25 % of the standard values, the odds of
tire blow up increase threefold; above 25%, the odds double.
Tire for the car is like the feet to human. The tire is the cars’ only component contacting the ground. Driving force and braking force come from the tire, so the safety of the tire is crucial. While the tire pressure monitoring system would play a great part in ensure tire to remain in the best situation.
In conclusion, installing Autel TPMS is essential, because undetected tire flat can result in serious consequences. If you want to avoid abnormal tire pressure in daily driving experience, checking the tire pressure frequently is the basic way. However, for those whose tire gets puncturing in the road, the air leak quietly. If it is left unattended, the tire would blow up in the end. A tire will be wasted. In this condition, have a tire pressure monitoring system is very significant. Nowadays, factory-fresh cars are seldom equipped with TPMS, but you can install it by yourself. The specialist suggests that if condition permit, a TPMS is quietly necessary.
If your car had some problems in TPMS, you can always buy car diagnostic tools from our website, and then diagnose malfunctions by yourself. These vehicle diagnostic tools are: Launch X431 V Pro, Launch X-431 PAD, Autel MaxiScan VAG405, and so on.
Posted by: obdtools at
08:10 AM
| No Comments
| Add Comment
Post contains 380 words, total size 4 kb.
January 13, 2015
How to improve car performance? Do you want to make your car go
faster? Statistics show that almost every car enthusiast wishes to add
more power to their car or wish to improve fuel-efficiency, but how to
achieve that? Well, actually car maintenance and repair service provider
may be the best solution for improving the performance of your car.
With the help of a professional, you will find how a car maintenance and
auto repair service can make your car go faster.
Installation of Supercharger
Superchargers are most commonly used by the repair service providers to
improve car's performance. With proper installation, it can produce
about 50% more horsepower. Wondering how does this work? After
installation, it pressurizes air intake to more than the normal
atmospheric level. This means, more air goes into the engine which burns
more fuel to generate more power. Spinning rate of a supercharger is
minimum 50,000 RPM. So your will behave like a more powerful vehicle.
Weight reduction technique
The first thing that a car maintenance and repair service does to
improve the performance of your car is reduction of weight. They follow
the basic rule here that lightweight things move faster. All the heavier
parts of the car are switched out with the lighter parts to make it
more aerodynamic. For instance, they replace the heavy glass windows
with acrylic versions.
Cold air intake kit installation
You may also be asked by the car repair service to install cold air
intake kit for better performance. Since the efficiency of your car
greatly depends on the air, a cold air intake kit will be effective.
Experts install this kit to bring cool air into the internal combustion
engine resulting higher performance and better engine efficiency. You
may know that colder air is denser than warm air, means it boasts more
oxygen than the hot air, so your car experiences a more dynamic
combustion in the engine leading to more power.
Better Air Filter
For better use of the air/fuel combination, repair experts also install
better air filters. Since air filters are made up of cotton and other
materials, they get damaged over time and degrade the performance of the
High-quality air filters are made of fabric. So they can be washed and
reused to enhance performance.
Performance chips installation
All the latest cars, comes with an onboard computer regulating things to
control the entire show. A good car repair expert knows the importance
of performance chips very well. To boost your car's performance, they
will install performance chips, to control functions such as timing,
anti-lock brakes as well as the all-important fuel-to-air ratio.
Performance chips are also known as super chips and they increase the
power of the engine and horsepower.
An expert from a reputed car repair company can help you out to improve the performance of your car. Consult one such expert and let the professional know what exactly you want in your car. Since they are quite experienced in this, they'll device a unique plan to make your car unique.
Except for the routine maintenance, if your car had some problems, you can always buy vehicle car diagnostic tools from our website, and then diagnose malfunctions by yourself. These vehicle diagnostic tools are: Launch Diagnostic Tool, Autel Diagnostic Tool, Autoboss Diagnostic Tool and so on.
Source: http://www.focalobd.com/blog/top-5-ways-to-improve-your-car-performance/
Posted by: obdtools at
07:47 AM
| No Comments
| Add Comment
Post contains 563 words, total size 5 kb.
January 08, 2015
If you buy a new in-dash DVD player in the internet, what the steps of installing it? The steps depend on the type of player that will work with your car. If you have a faceplate stereo, for example, you can get a faceplate DVD player, take off the stereo, and connect the DVD in its place. Some car types will require you to completely install the DVD player in the radio's place in the dashboard, and wire it to the car's power. You might need professional assistance, depending on your vehicle type and what must be done to make the player fit in the dash.
Things You'll Need: Wrench; Screwdriver; Trim stick, etc simple tools
Instructions
1. Disconnect the battery on your vehicle by loosening the clamp on the
black battery cable with a wench and removing the cable from its
battery terminal.
2. Remove the trim panel surrounding the radio.
Sometimes, you can just grasp and pull the panel off its clips. In many
other cases, you must pay it off with a flat trim tool.
3. Remove
the radio. The tools needed for the clips/fasteners can vary. Disconnect
the wiring harness and antenna lead in the back.
4. Remove the
steering column covers, usually by unscrewing the screws at the bottom
with a screwdriver and separating the two halves, to access the wiring
harness for the ignition switch/starter.
5. Feed the DVD's constant
power wire (usually the yellow one) through to the engine compartment;
there should be a hole in the firewall. Loosen the cable clamp for the
positive battery cable, fit the wire lead on the terminal, and tighten
the cable.
6. Insert the DVD's switched power wire -- usually the red -- into an available slot on the ignition switch's wiring harness.
7. Mount the DVD's black ground wire to a screw on the chassis --
loosen the screw with a screwdriver, and place the wire lead under it --
or a similar metal ground.
8. Install and fit the DVD player within
the dashboard where the radio was, using its fasteners and your
screwdriver/wrench. Reconnect the trim panels.
9. Reconnect the negative battery cable.
Whether working on auto shops or a cost-driven necessity, most DIYers and backyard mechanics are better off with inexpensive alternatives to expensive professional tools. There are some good Car Diagnostic Tool that can interface with your computer, phone, or tablet.
Posted by: obdtools at
07:12 AM
| No Comments
| Add Comment
Post contains 410 words, total size 3 kb.
32 queries taking 0.0623 seconds, 81 records returned.
Powered by Minx 1.1.6c-pink.